Logo
Filler wire , stellite rod, tungsten rod, ahmedabad Wire rod nickel wire, monel wire, titanium wire, gujarat Titanium wire, stainless steel sheet, india Filler wire, stainless steel pipes and rod, india stellite rod, tungsten rod, stainless steel pipe, india
Importers Stockist of...
Filler Wire Tig / Mig Stainless Steel
Aluminium Filler Wire
Titanium Alloys Filler Wires
Mild Steel & Low Alloy Steel Welding Filler Wire
Duplex Filer Wire
Nickel & High Nickel Alloy Filler Wire
Stellite Rods
Flux Cored Wire
Tungsten Rods
Products
Welding Electrodes / Filler Wire Tig/Mig
 
 
Grade
(AWS Specification)
Type
of Current
Typical All weld Deposit Analysis(%) Typical All Weld Mechanical
Properties
Applications
c si Mn Cr Ni Mo Other T.S. N/mm2 (Ksi) Elongation (%)
E307-16 AC
DC(+)
0.06 0.68 5.66 19.87 9.73 0.98 - 640
(93)
45 Welding dissimilar steel such as a welding austenitic manganeses steel to carbon steel forgings or castings.
E308H-16 AC
DC(+)
0.05 0.80 1.00 20.00 10.00 - - 600
(87)
40 For welding of low carbon steels of AISI 304 type where maximum resistance to intergranlar corrosion is required.
E308/E308L-16 AC
DC(+)
0.02 0.46 1.88 19.97 9.69 - - 590
(86)
45 For welding of 18% Cr - 8% Ni steel such as AISI Type 301, 302, 304, 305, and 308.
E309/E309L-16 AC
DC(+)
0.03 0.69 0.97 24.02 13.21 - - 588
(81)
44 For welding low carbon 22% Cr -12% Ni Steel,carbon steel or low alloy steel to stainless steel & stainless clad steel.
E309Cb AC
DC(+)
0.08 0.56 1.65 23.10 12.9 - Cb 0.79 Electrode is designed for special applications requiring columbium with 22% chromium and 12% nickel
E309 MOL-16 AC
DC(+)
0.03 0.65 1.10 23.71 12.84 2.31 - 606
(88)
41 For welding of type 316 clad steel or dissimilar steel.Corrosion resistant lining of carbon steels or low alloy steel.
E310-16 AC
DC(+)
0.10 0.41 2.19 25.98 20.75 - - 581
(84)
41 For welding of 25% Cr -20% Ni Steel and clad side of 18% Cr - 8% Ni clad steel. Perfect austenitic microstructure.
E310MO-16 AC
DC(+)
0.09 0.44 2.25 25.92 20.68 2.26 - 621
(90)
35 For welding of 25% Cr- 20% Ni -2% Mo Steel.Excellent corrosion resistance to sulfuric acid and good resistability to cracking and higher tensile
E310Cb AC
DC(+)
0.12 0.52 2.00 26.20 21.40 - Cb 0.79 Electrode is designed for special applications requiring columbium with 25% chromium and 20% nickel
E312-16 AC
DC(+)
0.09 0.67 1.62 28.75 9.39 - - 761 (110) 24 For welding of 29% Cr -9% Ni type cast steel. Joint welding difficult-to-weld steel. For a swear resistant build up and buffer layer for hardfacing.
E316/E316L-16 AC
DC(+)
0.02 0.38 1.58 19.27 12.27 2.23 - 540
(55)
47 For welding low carbon, molybdenum-bearing austenetic alloys. Welding of 18% Cr -12%Ni -2% Mo steel where the corrosion resistant qualities are reqiired.
E318-16 AC
DC(+)
0.06 0.67 1.76 19.07 12.66 2.24 NB & Ta 0.65 612
(89)
35 PS-318 is similler to PS -316 but contains niobium (Nb)to provide resistance to intergranular carbide precipitation.
E320-16 AC
DC(+)
0.05 0.40 2.02 20..9 34.54 2.34 NB & Ta 0.68 582
(84)
39 For welding alloys if similler composition in wrought &cast forms.Provides very good corrosion resistance to a wide range of chemical envioments.
E317L-16 AC
DC(+)
0.02 0.69 1.68 19.18 12.65 3.32 - 584
(85)
42 For welding AISI Types 317,317L.
E347-16 AC
DC(+)
0.05 0.44 1.73 19.93 10.06 - Cu3.42 NB &Ta 0.68 638
(93)
39 For welding of 18% Cr -8% Ni -Cb steel (AISI Type 321) and low carbon 18% Cr -8% Ni steel (AISI Type 304L)
E410-16 AC
DC(+)
0.08 0.38 0.46 12.80 0.10 - - 515
(75)
32 For welding pf 13% Cr steel. Surfacing of carbon steel to resist corrosion,erosion or abrasion.
E410NiMo-16 AC
DC(+)
0.043 0.27 0.33 12.18 4.52 0.068 - 600oC*5 hr For welding of 13%cCr steel. Surfacing of carbon steel to resist heat, corrosion, erosion and abrasion.
917 (133) 18
E385-16 AC
DC(+)
0.03 0.50 1.50 20.00 25.00 4.50 Cu 1.50 590
(85)
40 For welding of materials to similar chemical composition used in fabrication of equipment for handling sulfuric & phosphoric acid.
Nickel Alloy Welding Electrode
Grade Type of
Current
Typical All weld Deposit Analysis(%) Typical All Weld Mechanical Properties Applications
C Si Mn Fe Ni Mo Others Y.P.
N/mm2
(Ksi)
T.S.
N/mm2
(Ksi)
EI.
(%)
I.V.
oC,J
(oF,Ft-LBs.)
ENi-1 DC(+) 0.02 0.62 0.34 0.40 Bal. Ti
2.46Al
0.20
331
(48)
493
(71.5)
41 - For welding Nickel 200&Nickel 201 and also dissimiler metals. For good corrosion resistance especially in alkalies & low free carbon weld metal.
ENiCu-7 DC(+) 0.01 0.60 3.23 0.70 66.55 Cu
Bal
Ti
0.65
Al 0.17
338
(49)
508
(74)
40 - For welding monel 400,R405& K500 resistance to corrosion by sea water salts and reducing acids &For weld metals that meet stringent radiographic requirements.
ECuNi DC(+) - 0.26 1.15 0.65 30.22 Cu
Bal.
- 327
(47)
425
(62)
38 - For welding 70/30,80/20, 90/10 copper nickel alloys. Resistance to Fouling &corrosion in sea water.
ENiCrMo-3 AC
DC(+)
0.06 0.44 0.73 5.07 60.18 8.75 Nb&Ta
3.50
441
(64)
770
(112)
40 - For inconal 625,incolloy 825 & 25.6 Mo and other Mo Containning stainless steel. High strength at room or elevated tempreature & exceptional corrosion resistance including resistance to pitting,crevice corrosion & polythionicacid stress corrosion cracking.
ENiCrFe-1 AC
DC(+)
0.04 0.45 2.81 7.78 Bal. - Cr
15.53
Nb&Ta
2.78
623
(90)
382
(55)
42 -196o, 88
(-132,65)
For inconel 600,601 & innco330.Excellent high temperature strength, metallurgical stability &oxidatinresistance & can meet stringent radiographic requirements.
ENiCrFe-2 AC
DC(+)
0.04 0.15 2.90 8.05 Bal. 2.24 Cr
15.90
Nb&Ta
1.86
628
(91)
399
(58)
43 -196o, 93
(-132,69)
For incoloy 800,800HT and inconel 600, 601 and other nickel steels .Excellent strength and oxidation resistance at high tempreture and retain impact resistance at cyogenic temperature and retain impact resistance at cyogenic temperatures.
ENiCrFe-3 DC(+) 0.04 0.49 6.89 Bal. 3.20. 0.88 Cr
18.56
NB&Ta
2.22
654
(95)
373
(54)
49 -30o,100
(-22,74)
For inconel 600,601&inco330,Excellent high tempreture strength,metallurgical stability & oxidation resistance & can meet stringent radiographic requirements.
ENiCrFe-4 AC 0.15 0.78 2.20 8.00 Bal. 2.80 Cr
15.5
- 655
(95)
20 - For nickel steels in cryogenic applications. Same as Nickelarc A except for AC applications to minimiz magnetic or blow.
ENiCrFe-7 DC(+) 0.05 0.52 1.45 10.1 Bal. - Cr
29.5
Cb&Ta
1.2
- 670
(95)
44 - Welding of inconel 690, improve resistance to stress-corrosion cracking in nuclear ,pure water environments.
ENiCrCoMo-1 DC(+) 0.10 0.60 1.50 4.00 Bal. 9.50 Cr25 - 620
(90)
25 - For inconel 617,high strength, good metallurgical stability and excellent resistant to corrosion and high temperative oxidation.
ENiCrMo-4 AC
DC(+)
0.15 0.18 0.82 5.60 Bal. 16.2 W
4.07
476
(69)
734
(106)
43 - For welding inconel C-276 and other NiCrMo alloys. Corrosion resistance in many media and resistant to pitting crevice corrosion.
ENiCrMo-10 DC(+) 0.16 0.15 0.85 4.00 Bal. 13.5 Cr21.5 - 690
(100)
25 - For welding inconel 622& 625,incolloy 25-6 Mo& 825 excellent dissimilar welding electrode with protection against preferrential mild metal corrosion for Mo contains steels.
ENiCrMo-14 DC(+) 0.15 0.21 0.82 35.0 Bal. 16.0 Cr22.0 - 758
(110)
35 Hardness
95HRB
For welding duplex, super-duplex stainless steel-austenitic stainless steel and Ni-alloys (UNS NO6059 & 06022), inconel C276,622,625,amd 686,Corrosion resistance in pollution engine & chemical,petro-chem,oil or gas and marine industries.
Cobalt Base Alloys  Welding Electrodes
Grade Type of
Current
Typical All weld Deposit Analysis(%) Typical Hardeness of
all weld metal HRC(Hv)
Applications
c si Mn Cr Mo Other
ECoCr-C AC
DC(+)
2.15 0.47 1.03 31.25 - W
12.72
Co Bal.
50-56
(520-620)
For corrosion and high temperature abrasion.Hardfacing of valve heads,seal rings of high presure pump.
ECoCr-A AC
DC(+)
0.84 0.57 0.97 30.46 - W
4.53
Co Bal.
38-44
(370-440)
For corrosion and high temperature abrasion, Hardfacing of valve seats, forging dies,crushers and screws.
ECoCr-B AC
DC(+)
1.43 0.56 0.98 31.62 - W
8.67
Co Bal.
42-48
(410-490)
For corrosion and high temperture abrasion, Hardfacing sleeves of high pressure pump,cutting knives ,liners.
ECoCr-E AC
DC(+)
0.35 0.65 1.03 28.56 - W
0.38
20-32 This electrode is recommended for metal to metal abrasion and high impact applications involving high temperature and/or corrosive media.
Low Metal  alloys Welding Electrodes
Grade Typical All weld Deposit Analysis(%) Typical All Weld Mechanical Properties Applications
c si Mn Cr Mo Y.P.
N/mm2
(Ksi)
T.S.
N/mm2
(Ksi)
El.
(%)
PWHT
E8018-B2 0.06 0.61 0.70 1.32 0.55 590
(86)
670
(97)
25 690oC
*1 hr
For 1.25% Cr - 0.5% Mo steels.
E9018-B3 0.08 0.50 0.77 2.25 1.02 680
(99)
750
(109)
21 690oC
*1 hr
For 2.25% Cr - 1% Mo steels.
E8018-B6/
E502-16
0.06 0.40 0.78 5.25 0.51 560
(81)
660
(95)
21 740oC
*1 hr
For 5% Cr - 0.5% Mo low alloy steels welding.
E8018-B8/
E505-16
0.07 0.33 0.72 9.51 1.14 600
(87)
730
(106)
22 740oC
*1 hr
For 9% Cr - 1% Mo and 9% Cr - 2% Mo steels.
Super Duplex Stainless Steel Welding Electrodes
Grade Typical Analiysis of Filler Wire Applications
C Si Mn Cr Ni Mo Cu N
AWS E2594-16 0.030 0.5 1.5 25.0 9.5 4.0 0.7 0.23 E2594-16 is a superduplex coated electrode. The Pitting
Resistance Equivalent Number (PREN) is at least 40, thereby
allowing the weld metal to be called a superduplex stainless steel.
These coated electrodes provide matching chemistry and mechanical
property characteristics to wrought super duplex alloys such as 2507.